品牌：UD優道

系統：進排氣系統

產品編號：UD-02.271/325ml

企業標準：Q/YKJH 8

產品僅供4S店使用

產品特點：

1、本品采用美國專利技術，專業用于直噴發動機。

2、進行免拆清洗進氣歧管道、進氣閥門積碳，燃燒室 積碳，排氣門、排氣端渦輪葉片積碳。

3、改善發動機冷啟動困難，怠速不穩，加速無力油耗增大等現象。

4、提升進氣效率，燃油利用率，恢復發動機動力。

使用方法：

1、進氣門積碳清洗劑配合專用設備使用，汽車怠速情況下從進氣歧管吸入，施工時間控制在40分鐘。

2、油箱處理劑和發動機性能恢復劑直接加注油箱使用（每瓶兌40-60升汽油使用）。

項目優勢：

1、免拆施工：省時、省力，施工時間約40分鐘，只需配備壓縮空氣；

2、高性能產品組合，快速清除積碳，效果立即看得見；

3、環保配方，對橡膠、塑料、鋁鐵、氧傳感器、三元催化器等無損壞。

項目解決問題：

1、清除進氣門、進氣道積碳油污；

2、清除噴油嘴、燃燒室積碳；

3、去除油箱、油路去膠質、水分；

4、對解決發動機排放燈亮有明顯幫助；

5、恢復發動機新車性能、降低油耗、恢復動力、降低排放、降低噪音。

注意事項：

1、清洗過程中嚴格控制流量，確保施工過程在40分鐘左右。若施工過程中發現怠速抖動嚴重，立即關小控制閥流量直到正常為止。

2、清洗劑清潔完畢之后，保持發動機怠速行駛3-5分鐘，后加減油門排干凈殘余積碳。

3、在通風處施工。

4、對于進氣門積碳比較嚴重的建議：拆下歧管、手工清除。

Product features:

1. This product adopts American patented technology and is specialized in direct eruption motors.

2. Conduct no-disassembly and cleaning of inlet manifold and inlet valve carbon deposition, combustion chamber carbon deposition, exhaust valve and exhaust end turbine blade carbon deposition.

3. It is difficult to improve the cold start of the engine, unstable idle speed, weak acceleration and increased fuel consumption.

4. Improve the intake efficiency, fuel efficiency and engine power recovery.

Usage:

1. The carbon cleaning agent of the intake valve is used in conjunction with the special equipment. It is inhaled from the intake manifold in idling condition and the construction time is limited to 40 minutes.

2. Fuel tank treatment agent and engine performance recovery agent are directly injected into the fuel tank for use (each bottle is used with 40-60 liters of gasoline).

Project advantages:

1. No-demolition construction: save time and effort, and the construction time is about 40 minutes. Only compressed air is required.

2. High performance product combination to quickly remove carbon accumulation, and the effect can be seen immediately;

3. Environmentally friendly formula, no damage to rubber, plastic, aluminum iron, oxygen sensor, three-element catalytic converter, etc.

Project solution:

1. Remove carbon and oil pollution from inlet valve and inlet channel;

2. Remove carbon deposits in fuel injection nozzle and combustion chamber;

3. Degumming and water removal of fuel tank and oil road;

4. It is obviously helpful to solve the problem of engine discharge lamp on.

5. Restore new engine performance, reduce fuel consumption, restore power, reduce emissions and reduce noise.

Notes:

1. Strictly control the flow of water during cleaning to ensure the construction process is around 40 minutes. If idling jitter is found to be serious during construction, turn down control valve flow until normal.

2. After cleaning the cleaning agent, keep the engine idle for 3-5 minutes, and then add and subtract the gas pedal to clean the residual carbon deposits.

3. Construction in the ventilation area.

4. Suggestions for serious carbon accumulation in the intake valve: remove the manifold and remove by hand.